was successfully added to your cart.

Monthly Archives

May 2017

Site Safety – Power Saws

By | Uncategorized | No Comments

Careless or improper use of any power saw may cause a serious or fatal injury.  Keep in mind the following precautions to help reduce the risk of injury when working with a power saw:

  • Always wear the appropriate personal protective equipment (PPE). Eye protection, gloves, sturdy boots and protective clothing should be worn. You must wear goggles or properly fitted safety glasses with adequate top and side protection. Always wear heavy duty work gloves (e.g., made of leather or other wear resistant material) when handling the saw. Heavy-duty, nonslip gloves improve your grip and help to protect your hands. Wear sturdy boots with nonslip soles. Steel-toed safety boots are recommended. Clothing must be sturdy and snug- fitting, but allow complete freedom of movement. Avoid |oose—fitting jackets, scarf’s, neckties, jewelry, flared or cuffed pants, unconfined long hair or anything i ‘ that could become caught on any obstacles or moving parts of the unit or the material you are cutting.
  • Power table saws must have an upper guard that covers the entire blade of the saw; don’t remove the manufacturer’s installed guard and get them fixed if they do not work properly.
  • When using chain, brush, cut-off or any hand held saws, keep both hands on the saw to help prevent from being cut and have more control place your second hand on the auxiliary handle or motor housing. Keep your body positioned either side of the saw blade. Secure what you are cutting and never hold the material that you’re cutting.
  • After a cut, be aware of the necessary time it takes for the blade to come to a complete stop; be aware of the moving blade until it stops moving. Don’t run the saw while carrying it at your side.
  • Use your power saw within its limits. Know the type of blade and its uses; only use a blade that’s approved for the saw and material to be cut. Using an improper blade may cause it to shatter or crack in use causing it to be shot out at you or anyone in the area. Don’t use dull or damaged blades which can cause excessive friction, blade binding and kickback.

BE SAFE – Before you use any power saw be sure that you have the proper protective gear and are trained to operate the saw!

Site Safety – Scaffold Safety

By | Uncategorized | No Comments

Scaffold systems are an efficient and safe way of  providing a temporary elevated work platform. However, it is important to erect and use scaffolds properly as accidents can occur. The primary causes of scaffold accidents include failure of attachment points; footing, parts failure; inadequate fall protection; and adverse climate conditions (such as high winds). Falls are 80% of all scaffold injuries; of those injured, 60% involve skilled trades and 24% are laborers. Employees can prevent many of these accidents with good old common sense. Here are some things to keep in mind before using a scaffold:

General Guidelines for Using Scaffolds

  • Erect all scaffolds under proper supervision
  • lnsure that scaffolds and ladders are filmiy supported on dry, solid footings, plumb and properly secured
  • Do not install scaffolding on frozen, wet or un-compacted earth or with methods not recommended by the manufacturer
  • Inspect scaffold prior to use. Assign this task to a competent person.
  • Free all scaffolds of defective or damaged parts
  • Tie all scaffolds securely and safely into the structure
  • Ensure all structural members are adequate for use in proposed work
  • Check all connections and pins
  • Provide cross bracing
  • Have and use access ladders properly
  • Fall protection is required for workers on platforms 6 feet or higher.
  • Eliminate debris, ice, mud, from all ladders and working surfaces
  • Plank all working areas and service all planks
  • Inspect all scaffolds frequently. Overlap all planks by 12 inches
  • Train all employees adequately in use of scaffold and ladders.

When installing all guardrails, mid-rails, and toe-boards in work areas, make sure they meet the following strength requirements:

  • Guard-rails — height is 42″ (+/-3″) and at least 200 lbs. in strength
  • Mid-rails — set midway between guardrail & walking surface and 150 lbs. in strength
  • Toe-boards — typically 1″ x 4” construction
  • Working platforms/decks must be planked close to the guardrails
  • Planks – overlap on a support at by 12 inches.

BE SAFE — Before you use a scaffold, take the time to think it out. Use good judgment and common sense.

Site Safety – Protection of the Public on Job Sites

By | Uncategorized | No Comments

Contractors have the responsibility to protect their employees, subcontractors and the general public (including invitees to a construction project) from adverse safety and health conditions that can occur on a construction site.

They must also protect the public from nuisance conditions (i.e. ambient noise, dust), implement the necessary controls to avoid disruption of public routes and services and maintain a continuous separation between construction zones and public areas. Recent construction catastrophes in urban centers and suburban residential projects have significantly raised public awareness and concern of the Inherent dangers of construction.

Consider the following to help prevent injuries and accidents:  

  • Open excavations: Are they properly protected from site visitors others working on-site?
  • Existing utilities: Are they properly identified and marked?
  • Traffic routes (vehicular and pedestrian) is the safest route in use? Proper barricades?
  • Pedestrian routes including provisions for members of the public with special needs: Are they malntairiezi and in good condition?
  • Warning signs: Are they properly spaced. in good condition and illuminated (when required)?
  • Mobile equipment transport and usage: is there access in and out of the project?
  • Deliveries to the site and routine debris: is collection and removal properly planned?
  • Emergencies: Is there accessibility to the site by emergency medical services (EMS) and is there an effective Emergency Action Plan in place?
  • Falling and wind-blown objects: are there potential hazards that could injure or damage others’ property?
  • Illumination: is it adequate for nighttime visibility? is it directed away from a driver’s line of sight?
  • Vibrations or ground settlement: Are exposures evaluated and controlled?
  • Noise and dust from operations: Are they contained or controlled?
  • Inclement weather: Are provisions in place for drainage, water run-off and other exposures?
  • Communications: is a plan in place and coordinated with authorities. including community  relations?

KEEP JOB SITES SAFE AND PROVIDE ADEQUATE PROTECTION OF THE PUBLIC!